Home cable how to connect jumper cables to a 2017 ford escape

how to connect jumper cables to a 2017 ford escape

0
20

I. Introduction
A. Definition of Jumper Cables
B. Overview of 2017 Ford Escape

II. Preparing the Vehicle
A. Locate the Battery
B. Park the Vehicles
C. Turn off the Ignition

III. Connecting the Jumper Cables
A. Connect the Positive Cable
B. Connect the Negative Cable

IV. Starting the Vehicle
A. Start the Donor Vehicle
B. Start the 2017 Ford Escape

V. Conclusion
A. Disconnect the Jumper Cables
B. Drive the Vehicle
C. Take Vehicle to Mechanic

If you find yourself in a situation where you need to jump start your 2017 Ford Escape, you may be wondering how to go about connecting the jumper cables. Don’t worry, it’s actually quite simple. In this article, I’ll walk you through the steps of connecting jumper cables to your 2017 Ford Escape.

Jumper cables are an essential tool for any driver. They are used to jump start a vehicle when the battery has died. Knowing how to use jumper cables is an important skill for any driver, and it is especially important to know how to use them on a 2017 Ford Escape.

Preparing the vehicle is the first step in the process. First, locate the battery. It is usually located in the engine compartment. Next, park the vehicles close together, but make sure that they do not touch. Finally, turn off the ignition of both vehicles.

The next step is to connect the jumper cables. Connect the positive cable to the positive terminal of the dead battery. Then, connect the other end of the positive cable to the positive terminal of the donor battery. Next, connect the negative cable to the negative terminal of the donor battery. Finally, connect the other end of the negative cable to an unpainted metal surface on the 2017 Ford Escape.

Once the cables are connected, it is time to start the vehicle. Start the donor vehicle first, and then start the 2017 Ford Escape. If the Escape does not start, wait a few minutes and try again.

Once the Escape is running, it is time to disconnect the jumper cables. Start by disconnecting the negative cable from the unpainted metal surface. Then, disconnect the negative cable from the donor battery. Finally, disconnect the positive cable from the donor battery and then from the dead battery.

Once the cables are disconnected, the Escape is ready to drive. However, it is important to take the vehicle to a mechanic as soon as possible to have the battery checked.

Jumper cables are an essential tool for any driver. Knowing how to use them on a 2017 Ford Escape is an important skill. By following the steps outlined above, drivers can easily jump start their Escape and get back on the road.

III. Connecting the Jumper Cables

Connecting jumper cables is a simple process that can be done in a few minutes. It is important to follow the instructions carefully to ensure that the cables are connected correctly and safely.

Before connecting the jumper cables, make sure that the car with the dead battery is in park or neutral and the engine is off. The car with the working battery should be running.

Step 1: Connect one of the red clips to the positive terminal of the dead battery. The positive terminal is usually marked with a “+” sign.

Step 2: Connect the other red clip to the positive terminal of the working battery.

Step 3: Connect one of the black clips to the negative terminal of the working battery. The negative terminal is usually marked with a “-” sign.

Step 4: Connect the other black clip to an unpainted metal surface on the car with the dead battery. This will help to prevent sparks from occurring.

Step 5: Start the car with the working battery and let it run for a few minutes.

Step 6: Try to start the car with the dead battery. If it starts, let it run for a few minutes before disconnecting the jumper cables.

Step 7: Disconnect the jumper cables in the reverse order that they were connected.

It is important to remember that jumper cables should only be used as a temporary solution. If the car with the dead battery does not start, it is best to take it to a mechanic to have it checked out.

Conclusion

Connecting jumper cables to a 2017 Ford Escape is a relatively simple process that can be done in a few minutes. The process is the same for most vehicles, but it is important to make sure that the cables are connected correctly to avoid damaging the vehicle’s electrical system.

1. Park the two vehicles close together, but make sure that they are not touching.

2. Turn off both vehicles and set the parking brakes.

3. Open the hoods of both vehicles and locate the battery terminals.

4. Connect one end of the red (positive) cable to the positive terminal of the dead battery.

5. Connect the other end of the red cable to the positive terminal of the working battery.

6. Connect one end of the black (negative) cable to the negative terminal of the working battery.

7. Connect the other end of the black cable to an unpainted metal surface on the engine of the dead vehicle. This will help to ground the electrical system.

8. Start the working vehicle and let it run for a few minutes.

9. Try to start the dead vehicle. If it does not start, let the working vehicle run for a few more minutes and then try again.

10. Once the dead vehicle has started, disconnect the cables in the reverse order that they were connected.

11. Close the hoods of both vehicles and you are done.

FAQ

1. What type of jumper cables should I use to connect to a 2017 Ford Escape?

Answer: You should use jumper cables with a minimum of 4 gauge wire.

2. Do I need to disconnect the battery before connecting the jumper cables?

Answer: Yes, you should disconnect the battery before connecting the jumper cables.

3. Is it safe to connect the jumper cables to the 2017 Ford Escape?

Answer: Yes, it is safe to connect the jumper cables to the 2017 Ford Escape as long as you follow the instructions and use the correct type of jumper cables.

NO COMMENTS

LEAVE A REPLY

Please enter your comment!
Please enter your name here